图片
会员登录
登录账号:
登录密码:
验 证 码:
您好,您已登录
您有条新到站内短信
会员中心 退出登录
图片
点评搜索
 
 
点评详情
发布于:2018-1-4 00:19:46  访问:14 次 回复:0 篇
版主管理 | 推荐 | 删除 | 删除并扣分
Steel Vs. Wood Studs For Interior Walls
Lightweight framed construction is the most common construction system in michael kors handbags australia. New provisions in the 2009 and 2012 International Building Code will require the use of plate washers on most sill plate anchor bolts in engineered structures, such as multi-family and commercial projects, as well as one- and two-family homes designed using the IBC.
Sheathing are the sheets that are nailed over the studs to connect them securely and form the wall surfaces. While it may take many years to see the benefit of this, eventually you`ll see that you have used less resources to maintain a comfortable living space for yourself with using SIP frame construction over wood frame construction.
You can build a perfectly strong house with 40% less wood and increase the R-value of your walls by 50%. But the materials of the future will be smarter (more on that later), and framing redundancies will be gone. Naturally, it is also possible to choose different types of bracing for the lateral stability, such as steel stripping across the side of the framing or, as mentioned earlier, by opting for a structurally rigid cladding.
The rest of the build-up of a steel framing construction is very similar to that of a wood framing construction. If energy performance is your goal, big fat hunks of wood in walls that don`t need them is a good place to start. Structural engineers commonly assume that interior partition walls do not act as load-bearing elements, either due to the potential for future partition re-arrangement or structural inefficiency associated with close support spacings.
The horizontal leg of the angle is attached to the underside of the structural steel framing or concrete slab and the downward turned vertical leg of the angle is attached to the edge of the wall top plates through vertically-slotted holes. Reducing callbacks is all about paying attention to detail and keeping up with wood construction systems that deliver the best structural and building science performance.
People have been building with stud construction for countless years, so finding a qualified person to frame your tiny house will be easier than using any other method. Predictable: Unlike wood, which can arrive warped, twisted, or bent, steel studs (unless damaged) always arrive perfectly straight.
Studs shall be placed with their wide dimension perpendicular to the wall. Steel studs weigh one-third less than wood studs, making them easier to handle. National Association of Steel Framed Housing (NASH). In the case of C or U profiles, a soft insulating material such as mineral wool or fibers is put in between the studs.
While wood-frame construction makes it easy for builders to construct strong, durable buildings, wall studs alone can`t withstand high wind and seismic forces. A traditional wood-framed building requires a new coat of paint at least every four to seven years, with touch-ups on a regular basis.
Walls with staggered studs or double stud construction are most effective. When exceeding 4 feet (1219 mm) in height, such walls shall be framed of studs having the size required for an additional story. Over the objections of the wood products industry, the Sandy Springs City Council has approved a building code change to prohibit wood-framed construction for future buildings taller than three stories and larger than 100,000 square feet.
For all these reasons, wood framed construction is on the up and up. Industry innovators in Architecture and Engineering are proposing more high-rise designs utilizing primarily wood framing. The framing of exterior and interior walls shall be in accordance with provisions specified in Section 2326 unless a specific design is furnished.
Illustrated instructions describe each step, from constructing the walls to attaching the trusses to forming a complete roof, all in simple, easy-to-understand language. Snap a chalk line 2 in. below the lowest portion of ductwork or piping and nail a 2×4 to the wall studs at that point.
A single top plate may be used, provided the plate is adequately tied at joints, corners and intersecting walls by at least the equivalent of 3-inch by 6-inch (76 mm by 152 mm) by 0.036-inch-thick (0.90 mm)(20 gage) galvanized steel that is nailed to each wall or segment of wall by six 8d nails or equivalent, provided the rafters, joists or trusses are centered over the studs with tolerance of no more than 1 inch (25 mm).
共0篇回复 每页10篇 页次:1/1
共0篇回复 每页10篇 页次:1/1
我要回复
回复内容
验 证 码
看不清?更换一张
匿名发表 
图片
脚注信息

 

版权所有 贵州苗生药业有限公司
咨询电话:0859-3190677    地址:贵州省兴义市丰都办丰都社区10组